SEPINEO (TM) P 600 sohexadecane 100ML by Letco Medical Safety Data Sheet Section 1: Identification Common Name/Trade Name SEPINEO (TM) P 600 Supplier Information Letco Medical, LLC 1316 Commerce Drive NW Decatur, AL 35601 1 (800) 239-5288 +1 (734) 843-4693 IN CASE OF EMERGENCY: Chemtrec 1 (800) 424-9300 (24 hours) Product Synonym(s) N/A Relevant Use(s) of Product Manuf acture or Compounding of Substances Section 2: Hazards Identification Classification of Substance or Mixture Skin corrosion/irriation (Category 2) Signal Word Warning Hazard Statement(s) H315 Causes skin irritation Pictogram(s) Precautionary Statement(s) P264 Wash hands thoroughly af ter handling. P280 Wear protective gloves/protective clothing/eye protection/f ace protection. P302+P352 IF ON SKIN Wash with soap and water. P332+P313 If skin irritation occurs Get medical advice/attention. P362 Take of f contaminated clothing and wash bef ore reuse. Hazards Not Otherwise Classified No data available Ingredient(s) with Unknown Toxicity No data available Section 3: Composition/Information on Ingredients Chemical Name N/A Common Name Sepineo P 600 CAS Number N/A Material Percent CAS isohexadecane 20-40% 297-628-2 Impurities and/or Stabilizing Additives No data available Section 4: First Aid Measures General Advice May cause mild eye irritation. Exposure to decomposition products may cause a health hazard. Serious ef f ects may be delayed f ollowing exposure. Causes skin irritation. May be irritating to mouth, throat and stomach. If Inhaled Remove victim to fresh air and keep at rest in a position comf ortable f or breathing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artif icial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth to mouth resuscitation. Get medical attention if adverse health ef f ects persist or are severe. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as collar, tie, belt or waistband. In case of inhalation of decomposition products in a f ire, symptoms may be delayed. The exposed person may need to be kept under medical surveillance f or 48 hours. In Case of Skin Contact Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Continue to rinse f or at least 10 minutes. Get medical attention. Wash clothing bef ore reuse. Clean shoes thoroughly bef ore reuse. In Case of Eye Contact Immediately f lush eyes with plenty of water, occasionally lif ting the upper and lower eyelids. Check f or remove any contact lenses. Continue to rinse f or at least 10 minutes. Get medical attention. If Swallowed Wash out with water. Remove dentures if any. Remove victim to fresh air and keep at rest in a position comf ortable f or breathing. If material has been swallowed and the exposed person f eels sick as vomiting may be dangerous. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention if adverse health ef f ects persist or are severe. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain open airway. Loosen tight clothing such as collar, tie, belt or waistband. Most Important Symptoms and Effects Notes to physician: In case of inhalation of decomposition products under f ire, a symptom may be delayed. The exposed person may need to be kept under medical surveillance f or 48 hours. Page 1 of 4 Section 5: Fire Fighting Measures Suitable Extinguishing Media Use an extinguishing agent suitable f or the surrounding f ire. Special Hazards Arising From the Substance/Mixture In a f ire or heated, a pressure increase will occur and the container may burst. Decomposition products may include the f ollowing materials. Carbon dioxide, carbon moNOxide, nitrogen oxides, sulf ur oxides, metal oxide/oxides Special PPE and/or Precautions for Firefighters Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a f ire. No action shall be taken involving any personal risk without suitable training. Fire-f ighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a f ull f ace-piece operated in positive pressure mode. Section 6: Accidental Release Measures Personal Precautions, Protective Equipment and Emergency Procedures No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Avoid breathing vapor or mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. Methods and Materials Used for Containment Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor. Large Spill: Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses, basement and conf ined areas. Wash spillages into an ef f luent treatment plant or proceed as f ollows. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container f or disposal according to local regulations (see Selection 13). Dispose of via licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Note: See Section 1 f or emergency contact inf ormation and Section 13 f or waste disposal. Cleanup Procedures Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor. Large Spill: Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses, basement and conf ined areas. Wash spillages into an ef f luent treatment plant or proceed as f ollows. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container f or disposal according to local regulations (see Selection 13). Dispose of via licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Note: See Section 1 f or emergency contact inf ormation and Section 13 f or waste disposal. Avoid dispersal of spilled material and runof f and contact with soil, waterways, drains and sewers. Inf orm the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air). Section 7: Handling and Storage Precautions for Safe Handling Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and f ace bef ore eating, drinking and smoking. Remove contaminated clothing and protective equipment bef ore entering eating areas. STIR BEFORE USE. Conditions for Safe Storage Store in accordance with local regulations. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from compatible materials (see Section 10) and f ood and drink. Keep container tightly closed and sealed until ready f or use. Containers that have been opened must be caref ully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination. STORE AWAY FROM LIGHT AND HEAT (0-30 °C ) Section 8: Exposure Controls/Personal Protection Components with Workplace Control Parameters No special ventilation requirements. Good general ventilation should be suf f icient to control worker exposure limits, uses process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure below any recommended statutory limits. Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, f ume scrubbers, f ilters or engineering modif ications to the process equipment will be necessary to reduce emissions to acceptable levels. Appropriate Engineering Controls Wash hands, f orearms and f ace thoroughly af ter handling chemical products, bef ore eating, smoking and using the lavatory and at the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Wash contaminated clothing bef ore reusing. Ensure that eyewash stations and saf ety showers are close to the workstation location. PPE - Eye/Face Protection Saf ety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts. If contact is possible, the f ollowing protection should be worn, unless the assessment indicates a higher degree of protection: chemical splash goggles. PPE - Skin Protection Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. PPE - Body Protection Personal protective equipment of the body should be selected based on task being perf ormed and the risks involved and should be approved by a specialist bef ore handling this product. Appropriate f ootwear and any additional skin protection measures should be selected based on task being perf ormed and the risks involved and should be approved by a specialist bef ore handling this product. Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products is a risk assessment indicates this is necessary. Recommended f luor rubber, nitrile rubber. PPE - Respiratory Protection Use a properly f itted, air-purif ying or air-f ed respirator complying with an approved standard if a risk assessment indicates this is necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the saf e working limits of the selected respirator. Page 2 of 4 Section 9: Physical and Chemical Properties Appearance Form: Liquid [Emulsion] Colour: Opaque, White, Yellow tint Upper/Lower Flammability or Explosive Limits No data available Odor Faint odor Vapor Pressure No data available Odor Threshold No data available Vapor Density No data available pH 5 to 7 [Conc. (%w/w):2%] Relative Density 1,1 g/cm3 to 20 �C Melting Point/Freezing Point No data available Solubility Solubility Dispersible in the f ollowing materials: Cold water Initial Boiling Point and Boiling Range No data available Flash Point Closed cup:>102,5 �C (>216,5 �F) [ABEL/IP170/190.] Evaporation Rate No data available Flammability (Solid, Gas) No data available Partition Coefficient No data available Auto-Ignition Temperature No data available Decomposition Temperature No data available Viscosity 25 �C Section 10: Stability and Reactivity Reactivity No specif ic test data related to reactivity available f or this product or its ingredients. Chemical Stability This product is stable. Possibility of Hazardous Reactions Under normal conditions of storage and use, hazardous reactions will not occur. Conditions to Avoid No data available Incompatible Materials Oxidizing agents Hazardous Decomposition Products Under normal conditions of storage and use, hazardous decomposition products should not be produce. Section 11: Toxicological Information Acute Toxicity - LD50 Oral LD50 Oral Rat-Male, Female >5000 mg/kg Acute Toxicity - Inhalation LC50 Inhalation Dust and mist Rat-Male, Female 1,73 mg/l 4 hours Acute Toxicity - Dermal LD50 Dermal Rabbit-Male, Female >3000 mg/kg Acute Toxicity - Eye No data available Skin Corrosion/Irritation Irritating to skin Serious Eye Damage/Irritation No data available Respiratory or Skin Sensitazation No data available Germ Cell Mutagenicity No data available Carcinogenicity IARC No data available Carcinogenicity ACGIH No data available Carcinogenicity NTP No data available Carcinogenicity OSHA No data available Reproductive Toxicity No data available Specific Target Organ Toxicity - Single Exposure No data available Specific Target Organ Toxicity - Repeated Exposure No data available Aspiration Hazard Isohexadecane Page 3 of 4 Section 12: Ecological Information Toxicity Acute EC50>10000 mg/l Marine water ISO 10253 (2006) Algae-Skeletonema 72 hours. Acute LC50>3000 mg/l Marine water ISO 14669 (1999) Daphina-Acartia tonsa 48 hours. Acute LC50 >1000 mg/l Marine water OCDE 203 FishScophthalmus maximus 96 hours LC50>100 mg/l Literature Fish 96 hours Persistence and Degradability No data available Bio-accumulative Potential No data available Mobility in Soil No data available Other Adverse Effects No known signif icant ef f ects or critical hazards. Section 13: Disposal Considerations Waste Treatment Methods Product The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless f ully compliant with the requirements of all authorities with jurisdiction. Waste packaging should be recycled. Incerination of landf ill should only be considered when recycling is not f easible. This material and its container must be disposed of in a saf e way. Care should be taken when handling emptied containers that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Avoid dispersal of spilled material and runof f and contact with soil, waterways, drains and sewers. Waste Treatment Methods Packaging The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless f ully compliant with the requirements of all authorities with jurisdiction. Waste packaging should be recycled. Incerination of landf ill should only be considered when recycling is not f easible. This material and its container must be disposed of in a saf e way. Care should be taken when handling emptied containers that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Avoid dispersal of spilled material and runof f and contact with soil, waterways, drains and sewers. Special Precautions Landfill or Incinerations No data available Other Information No data available Section 14: Transport Information UN Number Not dangerous goods. UN Proper Shipping Name N/A Transport Hazard Class(es) N/A Packaging Group N/A Environmental Hazards N/A Section 15: Regulatory Information SARA 302-304: Composition on ingredients: Acrylamide 0-0.1% EHS Yes SARA 311/312 Immediate (acute) health hazard. Section 16: Other Information Additional Information Prepared By Lisa Russell Revision Date 01/09/2019 16:56 Disclaimer Letco Medical, LLC believes that the above information is correct but does not purport to be all inclusive and shall be used only as a guide. The information in this document is based on the present state of our knowledge and is applicable to the product with regard to appropriate safety precautions. If the product is used as a component in another product, this information may not be applicable. NO WARRANTY OF FITNESS FOR ANY PARTICULAR PURPOSE, WARRANTY OF MERCHANTABILITY OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, IS MADE CONCERNING THE INFORMATION PROVIDED ABOVE. Letco Medical shall not be held liable for any loss or damage resulting from handling, storage, use or from contact with the above product. Page 4 of 4
